Datsun Mini Truckin Homepage
Forum Home Forum Home > General > Tech Corner > How To
  New Posts New Posts RSS Feed - SR20DET  into a Datsun 620
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

SR20DET into a Datsun 620

 Post Reply Post Reply Page  <1234>
Author
Message
 Rating: Topic Rating: 1 Votes, Average 5.00  Topic Search Topic Search  Topic Options Topic Options
Braden620 View Drop Down
Moderator Group
Moderator Group
Avatar
Kentuckys Finest

Joined: 15 Jan 2010
Location: Somerset Ky.
Status: Offline
Points: 3064
Post Options Post Options   Thanks (0) Thanks(0)   Quote Braden620 Quote  Post ReplyReply Direct Link To This Post Posted: 15 Apr 2012 at 10:07pm
im nto sure what you are asking,   you have to have the wiring harness and ecu for the engine to run. 
If we ever forget that we are One Nation Under God, then we will be a nation gone under.
Ronald Reagan
Back to Top
Nissanboy View Drop Down
Junior
Junior


Joined: 31 Dec 2011
Location: Houston, TX
Status: Offline
Points: 31
Post Options Post Options   Thanks (0) Thanks(0)   Quote Nissanboy Quote  Post ReplyReply Direct Link To This Post Posted: 15 Apr 2012 at 11:35pm
Well I'm going to need to tune it so I'll probably best off getting a standalone. Didn't you get an AEM standalone? As far as the wiring harness I meant should I get the stock s13 harness or just better off configuring up one myself or try something like wiringspecialties.com? Hope that didn't sound too confusing lol
Back to Top
ShelbasoruS View Drop Down
Newbie
Newbie


Joined: 12 Aug 2012
Location: Australia
Status: Offline
Points: 2
Post Options Post Options   Thanks (0) Thanks(0)   Quote ShelbasoruS Quote  Post ReplyReply Direct Link To This Post Posted: 12 Aug 2012 at 9:13am
Looks good mate, Im about to start the same thing over here in Australia but i have a stock j15 in the ute atm... Any suggestions into how to go about mounting? should i get a set of the l20b mounts?
 
Cheers mate
Back to Top
Braden620 View Drop Down
Moderator Group
Moderator Group
Avatar
Kentuckys Finest

Joined: 15 Jan 2010
Location: Somerset Ky.
Status: Offline
Points: 3064
Post Options Post Options   Thanks (0) Thanks(0)   Quote Braden620 Quote  Post ReplyReply Direct Link To This Post Posted: 12 Aug 2012 at 9:39am
Shelb,  In your case, I havent got a clue.  You have a right hand drive model that came with the j 15.  Use my thread for reference only. Everything is backwards on your truck.
If we ever forget that we are One Nation Under God, then we will be a nation gone under.
Ronald Reagan
Back to Top
ShelbasoruS View Drop Down
Newbie
Newbie


Joined: 12 Aug 2012
Location: Australia
Status: Offline
Points: 2
Post Options Post Options   Thanks (0) Thanks(0)   Quote ShelbasoruS Quote  Post ReplyReply Direct Link To This Post Posted: 12 Aug 2012 at 10:39am
ok no problem mate :D will see how we go and will keep everyone updated
Back to Top
Braden620 View Drop Down
Moderator Group
Moderator Group
Avatar
Kentuckys Finest

Joined: 15 Jan 2010
Location: Somerset Ky.
Status: Offline
Points: 3064
Post Options Post Options   Thanks (0) Thanks(0)   Quote Braden620 Quote  Post ReplyReply Direct Link To This Post Posted: 12 Aug 2012 at 11:16am
I can help you with wiring if you need it though!
If we ever forget that we are One Nation Under God, then we will be a nation gone under.
Ronald Reagan
Back to Top
Nissanboy View Drop Down
Junior
Junior


Joined: 31 Dec 2011
Location: Houston, TX
Status: Offline
Points: 31
Post Options Post Options   Thanks (0) Thanks(0)   Quote Nissanboy Quote  Post ReplyReply Direct Link To This Post Posted: 24 Sep 2012 at 10:41pm
Hey Braden, I was test fitting the sr20 today and I have a few questions if you don't mind helping me out with. How was your clearance on your exhaust manifold/turbo? Reason I ask is because my sr20 almost fits on the stock mount location on the subframe. I just gotta flip the center link and if I reroute the coolant lines on the back of the motor I think it might fit! I dont know if the tranny will clear the floor pan as well though. 
Back to Top
EzCruiser View Drop Down
Admin Group
Admin Group
Avatar

Joined: 12 Jan 2010
Location: NE-TN
Status: Offline
Points: 3192
Post Options Post Options   Thanks (0) Thanks(0)   Quote EzCruiser Quote  Post ReplyReply Direct Link To This Post Posted: 24 Sep 2012 at 11:12pm
Sounds about right from the things I've read, have to wait on Dan-o!
Back to Top
Valvebounce View Drop Down
Newbie
Newbie


Joined: 18 Oct 2012
Location: New Zealand
Status: Offline
Points: 4
Post Options Post Options   Thanks (0) Thanks(0)   Quote Valvebounce Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2012 at 5:11am
Hey, how much clearance does the engine have on the underside of the hood?
I'd like to go a slightly different route to fit it.
Forced Induction!
Because everyone knows you don't bring a knife to a gunfight!
Back to Top
Braden620 View Drop Down
Moderator Group
Moderator Group
Avatar
Kentuckys Finest

Joined: 15 Jan 2010
Location: Somerset Ky.
Status: Offline
Points: 3064
Post Options Post Options   Thanks (0) Thanks(0)   Quote Braden620 Quote  Post ReplyReply Direct Link To This Post Posted: 02 Sep 2013 at 7:37pm
Wow sorry about the un-answered questions guys I really need to sit down and update this thread.
If we ever forget that we are One Nation Under God, then we will be a nation gone under.
Ronald Reagan
Back to Top
 Post Reply Post Reply Page  <1234>
  Share Topic   

Forum Jump Forum Permissions View Drop Down



This page was generated in 0.047 seconds.